How to Read a Digital Ohm Meter

Co-authored by Ralph Childers

Last Updated: November 24, 2022 Fact Checked

A digital ohmmeter (or ohm meter) is useful for measuring circuit resistance in electrical components. Digital ohm meters are far easier to read and use than their analog counterparts. The large digital display should show you the resistance value (a number, typically followed by a decimal point or two) and the scale of the measurement. Digital ohm meters vary slightly from model to model, so consult your user guide to ensure you're reading it accurately.

Method 1

Method 1 of 3:

Reading the Digital Display

Download Article

1
Determine the scale of the readout by looking for a “K” or “M” beside the omega. The omega symbol on your digital ohmmeter screen indicates the ohm level. However, if the resistance of whatever you're testing is in the kilo-ohm (1,000 ohms) or mega-ohm (1,000,000 ohms) range, the display will add a “K” or “M,” respectively, in front of the omega symbol.^{[1]
X
Research source}
- For instance, a reading that says 4.3 with only the omega symbol indicates 4.3 ohms. A reading that says 4.3 with a “K” before the omega symbol means 4.3 kilo-ohms (4,300 ohms).
2
Read the resistance value. Apart from understanding the scale of the digital ohmmeter, understanding the resistance value is the main element of the ohmmeter reading process. The numbers are typically front and center in the digital display, and usually extend to one or two decimal points.^{[2]
X
Research source}
- Resistance is a measure of how much a device or material reduces the electric current flowing through it. Higher numbers indicate a higher resistance rating, which means more energy will be required to integrate the component in a circuit.
- When you test a resistor, capacitor, or another electronic component, the ohmmeter will display a number indicating its resistance.
Advertisement
If you aren't using a meter with an auto-range function, you'll need to set the range yourself. To avoid setting the range too low, always start at the highest possible range and work your way down to lower ranges until the ohmmeter registers a reading. Do this even when you know the range of the component you're testing.^{[3]
X
Research source}

Method 2

Method 2 of 3:

Using the Meter

Download Article

1
Turn the meter on. The process by which your turn your ohmmeter on will vary depending on the model you're using. Typically, you can just thumb the switch that says “Power” or “On/Off.”^{[4]
X
Research source}
- Consult manufacturer directions for more information about how to select the resistance function on your multimeter.
2
Select the resistance function if you're using a multimeter. An ohmmeter is included in the suite of tools available in the multimeter, a device that also functions as an ammeter and voltmeter. The exact method by which you select the resistance function will vary somewhat depending on the model of multimeter you're using. Look for a rotating switch or dial to change the setting.^{[5]
X
Research source}
- Consult manufacturer directions for more information about how to select the resistance function on your multimeter.
In other words, don't connect the circuit to a power supply when using your ohmmeter. Doing so could damage your digital ohmmeter or invalidate your resistance reading.^{[6]
X
Research source}
4
Take individual components out of the circuit before testing them. If you want to measure the resistance of an individual component (for instance, because you suspect it is faulty), remove it from the circuit, then test the component by touching the leads to the two poles of the component. This will give you a baseline reading against which you can later test the circuit.^{[7]
X
Research source}
- The precise method by which you remove individual components depends on what the component is. For instance, if you're testing a capacitor, you'll need to remove it with a soldering iron and discharge any remaining electrical energy from it.
5
Test the resistance of an electrical component using the test leads. When you're ready to test components for resistance readings, touch the test leads to the leads of the component. These leads typically appear as two thin silver wires poking out of the component.^{[8]
X
Research source}
- Even within the same type of component, the placement of these leads varies. For instance, in some capacitors, the leads both exit the same side. In other capacitors, one lead will poke out of one end while the second lead pokes out the opposite end.
- If you're having trouble identifying the leads of the component you're interested in testing, consult manufacturer directions.
- It doesn't matter which test lead and which component lead you touch together.

Method 3

Method 3 of 3:

Setting the Range

Download Article

1
Use the auto-range setting if possible. Most digital ohmmeters have an auto-range function that eliminates the need for you to figure out the right range. This saves time and energy, and enables you to start using your ohmmeter sooner.^{[9]
X
Research source}
- The auto range setting might be inbuilt, or you might need to select it from a menu. Consult your user guide for more information.
2
Start at the highest range on your ohmmeter. Always set the range to the highest setting available when you first start testing to see if you can get an accurate reading. Hold the probes of the ohmmeter against the sides of the circuit to take your reading. If the range is too high, then the reading will stay on 0 or close to it.
- If you set an analog ohmmeter's range too low, it will cause the needle to snap rapidly to one side, potentially damaging it.
3
Turn the range down on the ohmmeter 1 step at a time to test the circuit. If the range is too high for a circuit, the reading may not be accurate or it will be hard to see. Use the range adjustment buttons on a digital meter or turn the dial lower on an analog meter to lower the range by 1 step. Test the probes on the circuits again to see if your reading is more clear. If not, keep adjusting the meter lower until you're able to see the reading.^{[10]
X
Research source}
- If you make adjustments to the ohmmeter's range, you may need to calculate the ohms using multiplication or division. Follow the instructions for your ohmmeter carefully to learn how to adjust your measurements.

Video

Expert Q&A

Search

Add New Question

Question

Is it possible to use a multi meter to check my a home breaker box?

Ralph Childers
Electrical Professional
Ralph Childers is a master electrician based in the Portland, Oregon area with over 30 years of conducting and teaching electrical work. Ralph received his B.S. in Electrical Engineering from the University of Louisiana at Lafayette and holds an Oregon Journeyman Electrical License as well as electrician licenses in Louisiana and Texas.

Ralph Childers

Electrical Professional

Expert Answer

Yes. With a multimeter, you can measure voltage, current, resistance, and other values depending on your meter.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 0 Helpful 1